Product Categories
Contact Us

Phone GPS Tracker

Technical Parameter: I nstructions: phone gps tracker Protocol explain: (013632782450BP05000013632782450101130A2234.0270N11405.9126E000.00623168.5400000005AEL0000067ET0CD) "(" stand for packet start "013632782450" stand for tracker ID "BP05" stand for command...
inquiry
  • Technical Parameter:

    Product N.W.

    0.1KG

    Band

    850/900/1800/1900Mhz

    GPS Module

    GT-1612

    GPS Accuracy

    5 meters

    Position Checking

    Mobile phone or Platform

    Standby Current

    <30mA

    Working Temperature

    -20°C to +70°C

    Functions :reset

    Remote restart GPS host

    Functions :number

    Set the SOS phone number

    Charging2

    lights off when fully charged

    Charging1

    Light on when charging;

    GSM fault

    Light flashing, restart every ten minutes


    Instructions:

    phone gps tracker Protocol explain:

    (013632782450BP05000013632782450101130A2234.0270N11405.9126E000.00623168.5400000005AEL0000067ET0CD)

    "("                 stand for packet start

    "013632782450"      stand for tracker ID

    "BP05"             stand for command

    "000013632782450"   also is tracker ID,you can use front

    "101130"            stand for data, 10 year 11 month  30 day

    "A"                stand for gps data valid,  "V" stand for gps data no valid

    "2234.0270"         stand for latitude, format is ddmm.mmmm

    "N"                stand for north, "S" stand for south

    "11405.9126"        stand for longitude, format is dddmm.mmmm

    "E"                stand for east,  "W" stand for west

    "000.0"             stand for  speed, unit is  km/h

    "062316"           stand for time,  06 hour 23 minutes 16 seconds, UTC time

    "8.5400"            stand for direction

    "000005AE"       stand for I/O state,first bit stand for main power, “0” stand for external power supply. “1” stand for battery supply. Second bit stand for ACC state, “0” stand for ACC off, “1” stand for ACC on. 

    Third, fourth, fifth reserved. The three bits of sixth, seventh, eighth stand for voltage value. The unit is 10mV,  Hex format. Value from 0 to 960, voltage from 0V to 24V. Such as 5AE is 5*16*16 + A*16 + E =1454 (10mV) = 14.54V

    This is the fuel sensor data

    "L"                stand for mileage flag

    "000067E"    stand for mileage value, hex format, 67E = 6*16*16+7*16+E=1662 meters.

    "T"                stand for temperature flag.

    "0CD"           stand for temperature value. Unit is 0.1 ℃, “0CD”= 0 * 16*16 +C*16+D=205,so is 20.5℃. When temperature is negative, the highest bit is 1, so “801” = -0.1℃,“802”= -0.2℃,and so on.

    ")"                stand for packet end

     

     phone gps tracker2238.png

     

    9) Cancel the continuous upload

    Text command

    Parameter

    Sample

    NUP

    NUP#

    NUP#

    Command

    Description

    This command is used to cancel sending data to the platform

    If need again to restore the upload , you need to send TIMEER Parameter setting  or STATIC

    Command Feedback

    SET OK!

     

    10)RELAY

    Text command

    Parameter

    Sample

    RELAYParameter1

    222#

    222#   cut off oil and power

    RELAYParameter2

    333#

    333#  recover oil and power

     

    Command Description

    1)RELAY control the start and closeness of the relay

    2) Only the center number can operate.

    3)the device only cut off the oil circuit on the condition of the driving speed below 20KM/H or in static state.

    4)When send the command, the device will reply “please waiting “When the vehicle speed is over 20KM/H, the device will cut off the oil or the power when the speed below 20KM/H.

    Command Feedback

    Successful Setting:Fuel cut has already been completed OK!

     

    phone gps tracker3145.png 

    phone gps tracker3147.png 


    phone gps tracker FAQ:

    Q1: After inserting a SIM card, it can get SMS command, but it display logoff or offline on the platform and APP.

    A: Please check that SIM Card has GPRS data plan.

    Q2: After set white list, cannot monitor.

    A: Please make sure the SIM card of the device has opened caller ID.

    Q3: Device show online, but it shows “wait for the device responses “when you set instruction with APP.

    A: a. Device signal is not good, so not smooth result of GPRS; b. Device is busy.

    Q4: The SIM card has GPRS data plan, but the

    device still show “logoff“ or “offline”.

    A: The tracker have pre-program all most APN, maybe the APN of the SIM card you use don’t preset in the tracker, Please set master number first and then send command to add you APN into the tracker.

    The command is: apn,apndata#

    Q5: phone gps tracker Device is not enabled

    A: Please check:

    1. ID number have not been added to the platform, contact supplier for support.

    2. SIM card is not installed correctly


    Hot Tags: phone GPS tracker, China, manufacturers, factory, low price